This site uses cookies to provide an optimized shopping experience. By using this site, you agree the use of cookies within our privacy policy.
Amprobe AT-6010/KIT
Advanced Wire Tracer Kit, 600 V AC/DC with AM-530 True-RMS Auto/Manual Ranging Electrical Contractor Multimeter
Amprobe AT-6010/KIT
Advanced Wire Tracer Kit, 600 V AC/DC with AM-530 True-RMS Auto/Manual Ranging Electrical Contractor Multimeter
The Amprobe AT6010KIT Advanced Wire Tracer Kit makes it easier and safer to locate energized and de-energized wires, breakers and fuses. When the transmitter is connected to the circuit, the receiver easily detects the signal in wires or cables behind walls, ceilings and floors.
- Receiver/Tracer operating voltage: 0 - 600 VAC/DC
- Receiver/Tracer operating frequency: Energized 6.25 kHz/De-Energized 32.768 kHz
- Receiver/Tracer measurement category: CAT III 600V
- Receiver/Tracer operating voltage: 0 to 600 V AC/DC
- Receiver/Tracer operating frequency: Energized 6.25 kHz/De-Energized 32.768 kHz
- Receiver/Tracer measurement category: CAT III 600 V
- Tracer hazardous voltage detection: > 30 V AC/DC
- Tracer current output of signal (typical):
- Energized circuit: HI mode: 60 mA RMS
- De-energized circuit: HI mode: 130 mA RMS
- Loop mode: 160 mA RMS
- Tracer signal voltage output (nominal):
- De-energized circuit: HIGH: 33V RMS, 140 Vp-p
- Receiver range detection (open air):
- Tip sensor (Energized):
- Max distance via air: up to 20 ft (6.1 m)
- Pinpointing: approx. 1.97 in (5 cm)
- Tip sensor (De-energized):
- Max distance via air: up to 14.7 ft (4.5 m)
- Pinpointing: approx. 1.97 in (5 cm)
- Receiver display size: LCD 2.5 in (6.35 cm)
- Power: 1.5 V AA Batteries
- Finds shorts and opens
- Transmitter "Loop" mode for closed loop de-energized circuits
- Two frequency modes for optimal tracing in energized and de-energized circuits
- Large LCD Receiver screen with two digit readout, bar graph and sound to easily determine wire location
- Simple one button Transmitter operation
- Compatible with the CT-400 Signal Clamp accessory (not included) for inducing tracing signal on cable when there is no access to bare conductors
Applications
- Trace energized and de-energized wires
- Identify breakers and fuses
- Connect to GFCI protected circuits
- Find breaks and opens
- Find shorts
- Trace wires in metal conduit
- Trace non-metallic pipes and conduit
- Trace shielded wires
- Trace underground wires
- Trace low voltage wires and data cables
- Sort bundled wires
- Map a circuit with test leads
- Trace breakers on system with light dimmers
AM-530 Features:
- Voltage up to 600V AC and 600V DC, AC/DC
- Current, resistance, Frequency, Capacitance, and Temperature
- True-rms
- VolTect™ Non-contact voltage detection
- Audible continuity
- Diode test
- Data hold
- Max/min memory
- Relative zero mode
- Built-in test leads storage and "third hand"
- test lead holder
- Auto and manual ranging
- Auto power off
- Low battery warning
- Safety rated: CAT III 600V
Wire tracing made simple
With the AT-6010/KIT Advanced Wire Tracer Kit, it's never been easier and safer to locate Energized and De-energized wires, breakers and fuses. When the Transmitter is connected to the circuit, the Receiver easily detects the signal in the wires or cables behind walls, ceilings and floors. The Transmitter works on Energized and De-energized circuits up to 600 V AC/DC in Category I through Category III electrical environments, allowing for work directly on an energized circuit without the need to take equipment offline. The Transmitter also features high signal mode for general tracing and a loop mode designed specifically for locating shorts, as well as two optimal tracing frequencies that are automatically activated based on the detected voltage. The complete AT-6010 kit features test leads and accessories International accessory kit for use outside North America.
The AT-6010/KIT also includes The Amprobe AM-530 True-rms Electrical Contractor Multimeter. The AM530 is the fully-featured multimeter of choice for the professional electrical contractor. Measure and verify presence of voltage in order to connect equipment or to perform repairs, run new wiring, check continuity of electrical connections, identify blown fuses, troubleshoot motors or check transformers. The AM-530 features true-rms sensing to accurately measure voltage on systems affected by harmonics, a built in flashlight to detect wire colors in the dark, a "third hand" probe holder and VolTect™ non-contact voltage detection.
Country of Origin | China |
---|---|
Brand | Amprobe |
Catalog | 5103770 |
Condition | NEW |
UPC | 095969915014 |
Vendor Alias | AT-6010/KIT |
- 1 - AT-6010-R Receiver
- 1 - AT-6010-T Transmitter
- 1 - AM-530 Multimeter
- 1 - CC-6010 Soft Carrying Case
- 1 - User Manual
- 1 - 1.5 V AA (Iec Lr6) Battery
- 1 - TL-6000-INTL test lead and accessory kit includes:
- 2 - 1 m test leads (red, black)
- 1 - 7 m test lead (green)
- 2 - Alligator clips (red, black)
- 2 - Outlet blade adapter (red, black)
- 2 - Outlet round adapter (red, black)